Search:

Type: Posts; User: rive

Page 1 of 16 1 2 3 4

Search: Search took 0.13 seconds.

  1. ADC-S2000-T-RA require zwave 4.55 ( ADC remote thermostat temp sensors)

    If you have the GoControl panel, and the ADC-T2000 tstat, and invested in the Remote Temp Sensors (Alarm.com Temperature Sensor ADC-S2000-T-RA), be aware that they will not properly work with a GC2...
  2. Replies
    7
    Views
    6,400

    The GC2 (aka CP21) does not have a built in POTS....

    The GC2 (aka CP21) does not have a built in POTS. Only the earlier (GC/CP1x) GoControl CP's do.

    The GC2/CP21 panels came out with zwave version 3.42. Panels that do not have the emergency symbols ...
  3. Replies
    4
    Views
    4,695

    The GC3 AT&T model is available. The 3G AT&T...

    The GC3 AT&T model is available.

    The 3G AT&T (3GA-A-GC3) alarm.com GC3 cellular module with built-in antenna runs $120 on ebay, and more dealers will have it shortly.
  4. Thread: GC3 User Guide

    by rive
    Replies
    1
    Views
    3,403

    Or you can just download the GC3 Installation &...

    Or you can just download the GC3 Installation & Programming Guide, or directly download it HERE
  5. Replies
    9
    Views
    7,888

    That would be incorrect. The original 2GIG...

    That would be incorrect.

    The original 2GIG Go2.0/skypanel (prior to UI software change)

    http://s28.postimg.org/xyx9ejo31/20140527_090527.jpg...
  6. Replies
    3
    Views
    8,864

    1.14 was buggy, and has since been replaced with...

    1.14 was buggy, and has since been replaced with 1.14.01.

    1.14.01 and 1.14 break the panel lockouts and flashing 1.13 after 1.14 or 1.14.01, will act as a hard panel reset, resetting entire panel...
  7. Replies
    9
    Views
    7,888

    Sorry that you wasted your money. the DW40 came...

    Sorry that you wasted your money. the DW40 came out long after the sky, and the sensor requires firmware 1.14/1.14.0.1 or higher (which isnt supported by the skypanel).

    Only 2011-2012 or older...
  8. Sticky: There is now a way to unlock any 2GIG GoControl...

    There is now a way to unlock any 2GIG GoControl panel using firmware.

    The process is to obtain a 2GIG-UPCBL2 Firmware update cable ($20 various online sources), then flash firmware 1.14/1.14.0.1...
  9. This is the center of house install what can you...

    This is the center of house install what can you do to that transformer? The panel is there, unplugging transformer power supply is useless.

    Is purely aesthetics. You can rip that power...
  10. You can't reuse the old panel or keypads. You...

    You can't reuse the old panel or keypads. You cannot reuse any wired CO, or smoke detectors (e.g., Life Safety devices).

    You can reuse any Honeywell compatible wireless smokes/sensors, and any...
  11. You can't use the TAKE for a siren. Either,...

    You can't use the TAKE for a siren.

    Either, wire it directly with a resistor, or replace it.

    See:
    http://www.2gigforum.com/threads/175-Bell-Siren-circuit-terminals-5-and-6-hot

    and...
  12. Thread: Sky Panel

    by rive
    Replies
    41
    Views
    151,202

    Nope. The sky panel doesn't support any of...

    Nope.

    The sky panel doesn't support any of that newer 2GIG equip. You can use a PAD1 though is my understanding (assuming you have installer access).

    The sky panel is basically compatible with...
  13. Replies
    4
    Views
    5,540

    Try resetting lock itself, and removing the lock...

    Try resetting lock itself, and removing the lock first from any existing zwave network. Then try adding the device again
  14. Sticky: To remove the vivint logo, the panel must be...

    To remove the vivint logo, the panel must be reprovisioned with OEM 2GIG firmware, and have a successful cell test performed (with a non-vivint module). This will initiate an OTA update to the panel...
  15. what is it you want to accomplish by resetting to...

    what is it you want to accomplish by resetting to factory default?

    Are Q44 and Q45 lockouts disabled?

    Do you want to reprogram all sensors and zwave devices from scratch?
  16. Thread: Z-wave Thermostat

    by rive
    Replies
    1
    Views
    2,451

    Yes it can be controlled via ADC, and it works...

    Yes it can be controlled via ADC, and it works fine with 2GIG.
  17. Replies
    4
    Views
    4,774

    the changes for firmware are posted. Did you not...

    the changes for firmware are posted. Did you not see it?

    As for zwave dimmer, try deleting rule/scene and recreating it.

    225
  18. Thread: PIR Not working

    by rive
    Replies
    6
    Views
    9,977

    he has the PIR1, and he is talking about the time...

    he has the PIR1, and he is talking about the time that it takes for the infared lense to initialize.

    0533 or 0869 equip codes are used with regular PIR motions. An Image Sensor uses equip code...
  19. Thread: PIR Not working

    by rive
    Replies
    6
    Views
    9,977

    Is it a Honeywell 5890 PIR? Or a 2GIG PIR with...

    Is it a Honeywell 5890 PIR? Or a 2GIG PIR with pet immunity?

    2-3 min is normal. You do know how a Passive InfraRed motion detector works, right?

    Here is how a PIR works......
  20. Thread: PIR Not working

    by rive
    Replies
    6
    Views
    9,977

    2GIG-PIR1? Improper install/programming. See...

    2GIG-PIR1?

    Improper install/programming. See the thread for PIR1 install and programming and verify you have the correct loop (loop 1), and zone type as (04) interior follower, etch

    See:...
  21. With the way the new cloud based storage is set...

    With the way the new cloud based storage is set up, you should not be using low res, low compression (quality), low frames (fps), or 30sec clips... or even the medium defaults.

    Cloud Storage is...
  22. You get local, and you can also configure cloud...

    You get local, and you can also configure cloud storage based on recording rules/events.
  23. Thread: 2 thermostats?

    by rive
    Replies
    3
    Views
    3,750

    yes for compatible zwave thermostat. The mesh...

    yes for compatible zwave thermostat.

    The mesh network of the 2gig panel can support up to 242 zwave devices.

    Line of sight zwave range is around 65' or so, and powered zwave devices act as...
  24. Replies
    4
    Views
    5,587

    The cell module is useless to you (unless it is...

    The cell module is useless to you (unless it is unregistered)

    Check module status: http://suretycam.com/cellular-module-check

    If its a vivint panel, don't even waste your time checking it.
    ...
  25. You are SOL on getting anything from Vivint ...

    You are SOL on getting anything from Vivint (customer service, techs are mostly under the impression the Go! Control panel is theirs and Vivint hardware)

    They do not support firmware above 1.9.6,...
Results 1 to 25 of 390
Page 1 of 16 1 2 3 4