PDA

View Full Version : DW40 Door/Window Contact with Bypass Button



locknalarm
07-11-2015, 08:54 PM
272

We are pleased to announce the new 2GIG Bypass Door/Window Sensor (2GIG-DW40-345). We are waiting on our stock order.
This micro-sized door/window contact gives you the ability to set a temporary bypass on a zone at the push of a button,
rather requiring you to disarm and then re-arm the security system.
After pressing and holding the integrated bypass button the sensor will remain bypassed until the contact closes again.
This features works with any version of the 2GIG GC2 Panel.
For GC2 Panels running firmware version 1.14,(yes 1.14 expect it to be out soon) bypass events are also logged in the System History.


SYSTEM REQUIREMENTS
GC2 Security Panel
Firmware Version 1.14 (for logging bypass events in the
System History) Will Work with all older version just wont log bypass 1.14 coming out soon

FEATURES
Bypass locally with integrated button
Bypass events logged in System History (requires firmware version 1.14)
Low-profile micro contact (1.5 x 1.0 x 0.4 in)
345 MHz frequency
SPECIFICATIONS
Wireless Signal Range: 275 ft (80 m) open-air with Wireless Control Panel
Code Outputs: Alarm; Alarm Restore; Supervisory; Low Battery; Tamper; Tamper Restore; Local Bypass Enabled*; Local Bypass Disabled*
Transmitter Frequency: 345 MHz (crystal controlled)
Supervisory Interval: 70 minutes
Bypass State LED: Red LED
Button: Local Bypass Button
Magnet: 5/8 max. gap
Sensor Dimensions (D x H): 1.5 x 1.0 x 0.4 in (3.7 x 2.5 x
0.8 cm)
Weight (including battery and magnet): 0.6 oz (15 g)
Housing Material: ABS Plastic
Color: White
Operating Temperature: 32 - 120 F (0 - 49 C)
Humidity: 5-95% Non-Condensing
Compatibility: 2GIG Receivers
Battery (included): CR2032 battery or equivalent
Certification: FCC, IC
*Code Output messages for these bypass events are logged in the System History on GC2 Panels running firmware version 1.14 or later

givemsm2
07-16-2015, 04:57 PM
...feature works with any version of the 2GIG GC2 Panel.
For GC2 Panels running firmware version 1.14

I am confused as the GC2 (GC2.0 panel) is known as the "Vivint Sky panel" and does not use firmware 1.13 or 1.14.

Are you instead refering to the GC panel (CNTRL1/CNTRL2)? This panel is commonly refered to as the "GC1" to differentiate it from the GC2.0 /Sky Control, and the upcoming GC3

Otherwise, I guess it is awesome that Vivint GC2 panel users will soon be able to use the DW40...

admin
07-16-2015, 05:25 PM
I am confused as the GC2 (GC2.0 panel) is known as the "Vivint Sky panel" and does not use firmware 1.13 or 1.14.

Are you instead refering to the GC panel (CNTRL1/CNTRL2)? This panel is commonly refered to as the "GC1" to differentiate it from the GC2.0 /Sky Control, and the upcoming GC3

Otherwise, I guess it is awesome that Vivint GC2 panel users will soon be able to use the DW40...

The DW40 will work with all versions of the GO Control CNTRL1 & CNTRL2 and the New GC3 When it comes out, With Firmware 1.14 (Coming out around September) you will have the ability to log the bypass